BEFORE PROCEEDING, REVIEW ALL WARNINGS IN WARNING TAB

When adjusting trigger weight: Never set the release lighter than one full turn clockwise (in) from the lightest setting.

To ensure you are at least one full turn in (clockwise) from the lightest setting you can back the internal set screw all the way out (counterclockwise) until it stops and then tighten it one full turn clockwise.

When adjusting trigger travel: Never set the release lighter than a 1/4 turn from the firing position.

To ensure you are at least a 1/4 turn from the firing position, first cock the release and then tighten the travel adjustment slowly (clockwise) until the release fires.

Once the release fires you will want to back the internal set screw out (counterclockwise) by at least a 1/4 turn.

After making Adjustments: Always test the release using a piece of string or a shot trainer before using a real bow.

Do not disassemble: Never disassemble the release for any reason. Never loosen the torx screws that hold the body together.

If you are having issues with UV Button please reach out to our customer service team at TeamUV@Ultraviewarchery.com.

HOW TO ADJUST

Thumb Button Location - Loosen the Trigger Bracket Bolt - move knob to desired location, then tighten the Trigger Bracket Bolt back down.

Trigger Travel - Move to desired location by adjusting clockwise for less travel or counterclockwise for more travel. Never set the release with less travel than a 1/4 turn from firing.

Trigger Weight - Adjust clockwise for more trigger weight, counterclockwise for less weight. Never set the release lighter than 1 full turn in from the lightest setting.

Cock the Release - Press on the Cocking Bar with your thumb until hearing and feeling an audible ‘click.’ Put the D-loop through the String Retainer - you may need to use your index finger or thumb to help guide the d-loop through the string retainer.

Fire release - Slowly add pressure to the Thumb Button with your thumb until it fires.

Additional Resource:

https://youtu.be/Z1SoBOgcVmo

BEFORE PROCEEDING, REVIEW ALL WARNINGS IN WARNING TAB

ADJUSTING THE HINGE 2

Use 0.050” allen key to unlock adjustment mechanism from the bottom of the release. Using the “click” and “fire” designations on the side of HINGE 2, adjust each moon using a 0.050” allen key.

Clockwise rotation will increase the speed of each respective moon (making it faster/hotter), while counter-clockwise will decrease speed (making it slower/colder).

SETTING UP HINGE 2 WITH A CLICK

Insert 0.050” allen key into bottom of release and loosen the locking mechanism.

Adjust the “fire” moon to a very slow/cold position, so as to reduce risk of release firing during initial setup phase.

Using a shot trainer or piece of string (not your real bow quite yet), adjust “click” moon until your HINGE 2 clicks at your preferred timing during your shot cycle.

Once desired click timing has been set, slowly increase the speed of the fire moon until your HINGE 2 fires at the proper timing in your shot cycle.

Enjoy your HINGE 2!

SETTING UP HINGE 2 WITH NO CLICK

Insert 0.050” allen key into bottom of release and loosen the locking mechanism.

Adjust the “fire” moon to a very slow/cold position, so as to reduce risk of release firing during initial setup phase. Using a shot trainer (not your real bow quite yet), adjust the “click” moon until your HINGE 2 clicks when you would like your release to fire.

Once desired shot timing has been set, increase the speed of the fire moon until it passes the click moon location, allowing the release to fire at the timing you set in step “d”.

BEFORE PROCEEDING, REVIEW ALL WARNINGS IN WARNING TAB

INSTALLING UV3/UV3XL ON AN ULTRAVIEW SCOPE ROD

Loosen set screws and remove lens cartridge. Insert square end of scope rod into the slot on the side of UV3/UV3Xl. Screw ½” mounting bolt through UV3/UV3XL housing into the scope rod, and tighten firmly.

Re-install lens cartridge, tighten set screws until finger tight.

INSTALLING AIMING DEVICES IN THE UV3/UV3XL

Loosen set screws holding in lens (front) cartridge. Remove lens cartridge (front cartridge) from UV3/UV3XL housing. Use allen key to pop front o-ring out of the cartridge.

Install pin ring or lens into cartridge with the curvature of the lens facing away from your eye.

Re-install o-ring that was removed in step “3”. Re-install lens cartridge into UV3/UV3XL housing.

Snug down set screws holding lens cartridge in UV3/UV3XL housing.

THREE BUTTONS ON THE TOP OF THE UV3/UV3XL LIGHT KIT

The single button towards the middle of the scope controls on/off power, as well as the illumination of the level light

The two buttons towards the front of the scope are for adjusting light brightness -- left is dimmer, and right is brighter.

TO TURN ON YOUR UV3/UV3XL LIGHT

Fully press the button closest to the center of the scope for 2 seconds, then release.

TO TOGGLE THE LEVEL LIGHT

Turn light kit on. Press and hold the power button for 2 seconds, then release. Repeat step 2 to turn off level light.

BEFORE PROCEEDING, REVIEW ALL WARNINGS IN WARNING TAB

Remove stock grip from the bow riser.

Remove ALL factory adhesive from the riser.

Remove BeeReal Grip from its packing.

Place BeeReal Grip onto the bow riser grip section and gently push into place.

BEFORE PROCEEDING, REVIEW ALL WARNINGS IN WARNING TAB

Using an allen key, remove current grip. Align grip holes with screw locations and attach.

IMPORTANT: Use only the screws that came with your bow or the screws that are included with the grip.

THE BLACK SCREWS ARE FOR THE CARBON LEVITATE. THE SILVER SCREWS ARE FOR ALUMINUM BOWS.